Roller shutter model TP 8, knitted rectangular 240 mm (about) in width and 50 mm (about) in height.
Made with 8 mm diameter stainless steel pipes. AISI 304 and plates with round edges of 62 mm of pitch and of 20 / 10 of thickness in Stainless Steel. AISI 316, 12 / 10 thickness, with thick 50 / 10 stiffening angle, with lock if required.

Pair of U-shaped guides from 40x27x40 in extruded aluminum natural anodised or painted as desired, complete with anti-tear system and anti-noise sliding gaskets.

Rectangular mesh shutter particularly suitable for prestigious shops and exhibitions, where an innovative type of closure with an unconventional design is required.

The rolling diameter is very small in comparison to that of all the other meshes, consequently allowing the use of this type of shutter also in casings normally sized for roller shutters.

The rectangular mesh is from 100 mm (approx.) Wide x 10 mm (approx.) High, made entirely of stainless steel. with weft in round stainless steel. AISI 316 of 4 mm in diameter, spaced from the warp in triple braid in Stainless Steel. AISI 316 of 2,8 mm in diameter each.

Stainless steel end part. AISI 316 mirror-polished, consisting of 45 mm plate height and 50 / 10 thickness, and a corner stiffener from 50x30 mm and 30 / 10 thickness.

Anti-tear side retainers each 250 mm (approximately) in height.

Pair of U-shaped guides from 40x27x40 mm in natural anodized extruded aluminum complete with anti-tear system and anti-noise sliding gaskets.

Roll-up shutter with rectangular mesh with a proportioned design that allows excellent visibility of the showcase.

The rectangular mesh is from 240 mm (approximately) width x 45 mm (about) height, made of extruded aluminum plate from 20 mm x 50 / 10 mm thick worked at the ends with tear-proof recesses every four elements and with spacer connecting rods made from 10 mm diameter tube.

Oven-lacquered finish with thermosetting paints in any RAL shade.

End section closed with tubular section from 100 mm height, with abutment squares (on request).

Pair of U-shaped guides from 40x27x40 mm in natural anodized extruded aluminum complete with anti-tear system and anti-noise sliding gaskets.

Rolling shutter, made of 6 polycarbonate sheets mm thickness MAKROLON UV transparent, which allow an excellent level of light transmission, close to 85%, and at the same time avoids the color variation of what is exposed to direct sunlight.

The sheet is composed of two profiles in natural anodised extruded aluminum in compliance with UNI EN 150 7599 of 9 / 2010, coupled with hinged and shaped functions to receive the slabs. The pitch of the sheets is variable to allow the overlap of aluminum on aluminum only.

The aluminum profiles and the plates are locked sideways

Pair of U-shaped guides from 64x36x64 mm in natural anodized extruded aluminum complete with anti-tear system and anti-noise sliding gaskets.

The Stravedo polycarbonate shutter has the RC3 certification: resistance to burglary and classification (resistance under static load, resistance under dynamic load and resistance to manual burglary action) according to UNI EN 1627 standards: 2011, UNI EN 1628: 2011, UNI EN 1629: 2011 and UNI EN 1630 : 2011 of motorized damper.

Roller shutter model MONOPARETE, composed of strung elements, of different section and thickness, with special protection of the hook that, in addition to making the maneuver easier, keeps the joint unaltered from the damage of condensation, dirt and dust that could penetrate. In addition to the L-shaped profile, the beating element, with a higher thickness, is provided with sturdy locking handles and stopping rails.
The mantle runs in steel U-rails of suitable sections. This type of damper is available in steel
The aluminum profiles and the plates are locked sideways
Recommended for commercial closures for which it is not necessary to view the goods displayed during closing. It is the most traditional solution to protect shops, warehouses, garages, etc. against vandalism.

U-shaped rails from 64x36x64 in anodized extruded aluminum with anti-noise gaskets inside and with tear-proof seals for widths up to 4000 mm.

The single perforated lath element is 120 mm high and 10/10 thick.
Obtained from continuous coils perforated during manufacturing. The hole is circular with 4 mm diameter, 6 mm pitch and 40% porosity.
The bottom rail is 150 mm high and is completed with handle and bottom seals.

On request:

• Elements are supplied with restraints to avoid slip off as well to resist wind and/or tearing.
• Anti-tear and / or windproof can be applied.
• Number of blind elements above the base.
• Finished of the base.
• Angular stop, handle and stop teams.